ChrisEll Posted February 17, 2018 Author Share Posted February 17, 2018 I've just put a post up on how to adjust AVX axes. 1 Link to comment Share on other sites More sharing options...
ChrisEll Posted February 17, 2018 Author Share Posted February 17, 2018 Quick update on the AVX motor pinion situation... I am waiting for some pinions to arrive. In the meantime I've been experimenting with different ways to fix the pinion to the motor shaft... the new pinions do not have a boss and grub screw so will need to be glued on with something like Loctite or JB Weld. Hopefully I'll have something interesting to post in a few weeks. Link to comment Share on other sites More sharing options...
iapa Posted February 17, 2018 Share Posted February 17, 2018 thanks, planning to look at trying this tomorrow Link to comment Share on other sites More sharing options...
Fspp369 Posted February 28, 2018 Share Posted February 28, 2018 hi just been looking at your avx strip-down… on the pics of the worm drives they don't show locknuts on the end of the backlash adjusters… are they supposed to be there? great article btw. Link to comment Share on other sites More sharing options...
ChrisEll Posted February 28, 2018 Author Share Posted February 28, 2018 1 hour ago, Fspp369 said: hi just been looking at your avx strip-down… on the pics of the worm drives they don't show locknuts on the end of the backlash adjusters… are they supposed to be there? great article btw. Not sure which pics you're referring to... maybe to @Shelster1973 's posts? Link to comment Share on other sites More sharing options...
Shelster1973 Posted February 28, 2018 Share Posted February 28, 2018 2 hours ago, Fspp369 said: hi just been looking at your avx strip-down… on the pics of the worm drives they don't show locknuts on the end of the backlash adjusters… are they supposed to be there? great article btw. From what I can remember, yes they do have a lock-nut on them. You have to remove this to get the worm out. It is a snug fit in there and they do need a wee tap to get them out, but come out clean and easy. The one you can see in the pics was missing yes, but was replaced later on...... I think Link to comment Share on other sites More sharing options...
ChrisEll Posted March 10, 2018 Author Share Posted March 10, 2018 My AVX motor pinion replacement finally arrived. The only suitable gear I found were 5mm in height with no boss or grub screw. This meant bonding the new gear to the motor with glue. First job was to check it's the right diameter bore, so I removed the optical wheel off the back end of the motor and tried the gear there... perfect fit. I removed the RA motor, PEC sensor and control panel all as one piece, much easier than removing the motor from the control PCB. Also you can spin the motor using the handset. So the motor went in the vice and after many failed attempts to lever off the pinion with a screwdriver I eventually removed it by gripping the motor in my left hand rather than the vice. The pinion was hammered on very tight and was only held in place by friction... no keying or splines. Next to prep the bonding surfaces... I scored some lines inside the gear hole to give the glue something to grip onto, ditto the motor shaft. Quick clean then I put a small piece of masking tape at the base of the motor shaft (make sure the gearbox base can sit back on the motor without the masking tape interfering). This prevents any wayward glue entering the motor and also I can use it to help position the new pinion at the correct height. I put the gearbox base back on with the 2nd gear to get the correct height - I jiggled the masking tape accordingly. The new pinion is 5mm in height so only 3mm of it will actually bond to the motor shaft, not ideal but hopefully enough. Now to glue it on. I used Loctite 638, a "high strength retaining compound". I smeared some onto the motor shaft and inside the pinion using a tiny screwdriver, then a small blob into the hole and fitted the gear to the required height. I expected to have a bit of time to jiggle it and double check the height but the glue set very quickly and I was not able to move it. Luckily it was at the right height. I spun the motor using the handset to check the gear ran true which it did, much better than the original pinion. I left it for an hour and then scooped out the small pool of residual glue from the top of the pinion... this is not going to set and it's good to get rid of it now to help the curing process (Loctite only cures in small spaces in the absence of air). Left overnight. Next day I reassembled everything and switched on the mount. I could see the RA gears start to turn very slowly. I manually slewed the mount in ever increasing speeds, finally reaching 9... it worked fine. More slewing and then I left it on for the day at sidereal speed. I also loaded the mount with scope, camera, etc. (this is only a 5kg payload, the AVX can handle up to 16kg... I should test with a max payload sometime). So after all that here are the results. The high frequency periodic error is gone and the RA RMS has dropped considerably. Success! N.B. In case you need to remove the gear for any reason here's how: you need to apply heat to the Loctite, so hold the gear in a match flame for about 3 seconds then pull the gear off immediately. N.B.B. No need to do this mod on the Dec motor. 1 Link to comment Share on other sites More sharing options...
Shelster1973 Posted March 10, 2018 Share Posted March 10, 2018 Great news Do you have a link to where you got the pinion from? With all the awful weather at the moment I think I will strip mine down and change it. I do need to look at it again as after my last rebuild the worm is not as it should be as you can see a wobble when flexing the counter weight bar. Is just a case of finding the sweet spot of tightening Alan bolts and not binding the worm. Is a pain having to have the motor off to do it too..... Link to comment Share on other sites More sharing options...
ChrisEll Posted March 10, 2018 Author Share Posted March 10, 2018 I bought mine here: http://www.dancingwingshobby.com/free-shipping-rc-model-metal-pinion-gear-04m-23mmhole-diameter-8t-9t-10t-12t-13t-14t-15t-18t-20t-24t-height5mm-10mm-12mm_p0558.html Takes about 2 weeks. They come in fives, so I have some spare, so PM me and I'll pop one in the post if you like Anyway have a look first and see if your pinion does run off-centre... I thought you said it was all ok? Link to comment Share on other sites More sharing options...
Shelster1973 Posted March 10, 2018 Share Posted March 10, 2018 Will do It did not appear to wobble but am always one to tinker and fettle Link to comment Share on other sites More sharing options...
ChrisEll Posted April 15, 2018 Author Share Posted April 15, 2018 A similar issue with an EQ3 Pro mount Link to comment Share on other sites More sharing options...
swordfishy Posted May 3, 2019 Share Posted May 3, 2019 Howdy. I have a similar issue with a CGEM mount. 2 motors with 2 plastic gears missing teeth. I cannot find a source for the plastic gears, willing to go brass if I must. Any idea where a good place to look may be? Link to comment Share on other sites More sharing options...
swordfishy Posted May 3, 2019 Share Posted May 3, 2019 On 21/01/2018 at 10:23, ChrisEll said: After discovering a periodic signal (once every 11 seconds) in my guiding in the RA axis I did a bit of digging and found the motor pinion rotates 1 rev/11 sec at sidereal rate. By motor pinion I don't mean the big brass spur gear visible with you take the cover off... I mean the output from the motor before the reduction gearbox. When I spin the motor at a fast speed you can easily see that the pinion wobbles about which is not a good thing. The pinion is simply hammered onto the somewhat thin drive shaft rather than held in place by a grub screw. Dec motor wobbles the same. On the Celestron website there are photos of the CGX and CGEM motors and they look exactly the same... this may suggest the wobbly pinion is not an issue ? I then opened up the encoder. Nothing odd there but the optical wheel was worryingly grubby so I cleaned it with a damp cotton bud. There were markings on the PCB: "E8300 Rev.A RoHS". Time to open up the gearbox. Inside are 4 pairs of cogs. The gear ratios are: Motor pinion (9 teeth) -> 2nd gear (27 teeth) ==> 1:3 3rd gear (11 teeth) -> 4th gear (33 teeth) ==> 1:3 5th gear (11 teeth) -> 6th gear (33 teeth) ==> 1:3 7th gear (16 teeth) -> 8th gear (32 teeth) ==> 1:2 Overall reduction 54:1 Motor output speed 1 rev/ 11 sec Worm period: 11*54 = 594 seconds Note 2nd, 3rd and 4th cogs are plastic, possibly ok due to the low torque at that stage although someone here on SGL has experienced a split gear. I found that cleaning off all the excess grease results in a much smoother gearbox. I was tempted to open the motor casing itself but thought better of it So I was left with what to do about my RA high freguency periodic error... in the end it seemed a good idea to swap the Dec and RA motors over to see if that would help, especially as I had everything in pieces. Also my RA motor has had a hard life so far... my RA axis had been very, very tight - so tight I could not turn the worm by hand. This was due the tension ring being ridiculously overtightened and also the worm mounting bottom bolts being completely loose so the worm was not seated against on the ring gear properly. I only recently fixed this. I'm surprised the motor had not burnt out or a plastic gear split. I'm hoping it may have developed a slight problem and that the swap will help, though I admit it's a long shot. So will test shortly and see what the outcome is Any idea where we can find the nylon gears? Mine is stripped. CGEM, and I cannot for the life of me find any information on it. Anything would be appreciated! Link to comment Share on other sites More sharing options...
ChrisEll Posted June 12, 2019 Author Share Posted June 12, 2019 On 03/05/2019 at 03:21, swordfishy said: Howdy. I have a similar issue with a CGEM mount. 2 motors with 2 plastic gears missing teeth. I cannot find a source for the plastic gears, willing to go brass if I must. Any idea where a good place to look may be? You probably have to buy a whole motor replacement for each... i've not come across any gearboxes which are the same as the ones for the those motors. The broken teeth seem to suggest the RA and Dec axes are far too tight... the axes are not well assembled and tend to be overly tight. They can be easily corrected. 1 Link to comment Share on other sites More sharing options...
ChrisEll Posted January 15, 2020 Author Share Posted January 15, 2020 Another thought: only operate the mount when the mount is properly balanced otherwise you will overly stress the motors and gears. Link to comment Share on other sites More sharing options...
Kevin Holtz Posted December 5, 2020 Share Posted December 5, 2020 Found this topic. Here's a video of the pinion gear on my AVX RA motor running in sidereal rate. Its stopping every 3 seconds or so. You can really feel some stickiness in the motor when it overcomes it. Funny thing is, if I were in the Southern Hemisphere it would guide well...as it works great the other direction. New motor on order. https://youtu.be/Rq8LdA_dfRo Link to comment Share on other sites More sharing options...
billhinge Posted December 6, 2020 Share Posted December 6, 2020 I had a CG5 - I replaced the worm bearings with ABEC-7's (skateboard bearings) and replaced the RA bearing with a FAG HSS7007 (ABEC 7) https://www.247industries.com/s/en/bearings/HSS7007-C-T-P4S-UL-FAG/651477?currency=GBP - fits like a glove. I believe the AVX uses the same parts. Still got the old RA bearing. Also DIY belt modded it with highest quality parts I had to buy a new motor, I broke the original encoder doing a full motor tear down (I wanted to see what was inside 😉 - everything was lubed with WS2) I was going to rewire the motor housings to reduce noise (the plastic housing is like a sound box) but then someone was selling a commercially tuned new EQ6-R so I bought that instead and the CG5 is just sitting around for a future project Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now