Skipper Billy

Awesome and shows real dedication. Do you mind me asking where you got your Timelapse+ View from?? I cannot find a UK supplier and I don't like buying from the USA.

Cheers guys.

The Tadpoles and friends. Tadpoles (IC410) and the Spider Nebula (IC417) and the Fly (NGC1931). Imaged on 28th/29th November 2019. 3 hours Ha and 2 hours each of SII and OIII - all binned 1x1. Tak 106 with Atik 16200. Fully calibrated and processed in Pixinsight. To be honest I am really disappointed with the framing - I think I was trying to squash too much in the frame - I should probably have concentrated on the Tadpoles in the centre of the image. Hi res here - https://www.flickr.com/photos/113316085@N05/49147382488/in/album-72157675109735132/

I dithered between every sub - makes it even more strange !

In the image above it is largely processed out - it is very noticeable in the individual subs - particularly the 2x2 subs. AFAIK its a column of pixels that just doesn't work.

Hi. I make a calibration file library at the start of the season and the column defect isnt in any of them so it must have just appeared. I guess I will have to make a new library but I will see what FLO say first. All the best.

I hope so - its under warranty - although I think I read somewhere that dead columns are not a warranty issue. 😮 I have just emailed FLO so fingers crossed.

Dead column ???

The Pleiades - M45 - Takahashi 106, Atik 16200, Atik EFW3 filter wheel, Baader 2" broadband filters, Mesu 200 mount guided with SW ED72 and ASI 290 mono. Software - SGP, PHD2, processed In Pixinsight using the new WBPP script and fully calibrated with darks, bias and flats. 5 hours exposure @ -30º - 3 hours Lum binned 1x1 and 40 mins each RG and B binned 2x2. Hi -Res here - https://www.flickr.com/photos/113316085@N05/49128562801/in/album-72157675109735132/ Just discovered I have a dead column in my new camera! Vertically about 80 - 85% across to the right of the image. 😞

Have you run your images through CCD Inspector - its very good at helping to identify what the issue is. If you dont have the programme then email me a single unprocessed sub and I will run it through the programme and send you the results. My email address is on the 'Contact Me' page of my website.

Es Reid is the guru in the UK but I dont know how to contact him sorry. Try FLO - they offer an Es Reid collimation checking service with Es so they must know how to contact him. I think https://www.rothervalleyoptics.co.uk/ also offer a similar service (I havent used them but I am sure I read somewhere that they can do this.) Good Luck!

An interesting and enlightening 20 mins with your headphones here - https://www.bbc.co.uk/sounds/play/p05wsk5z

Fascinating - it looks like its 'breathing'!

Just a wee update The beta version in Frank's link works beautifully. Connected first time.

I would do but it doesn't fail - it just kept going round in circles but never solving and never failing.

I have a fairly low spec Intel NUC velcroed to the side of my scope - all USB and power cables custom made to the correct length (I am bit OCD about that) 😉 Only one cable from the scope to the ground ! For connectivity the NUC communicates wirelessly with a Powerline adapter about a metre away and my indoors PC does the same. (The obsy is on the same ring main as the dining room.) I use RDP in windows and it works flawlessly. Some photos here.......

Just a wee update - I changed the primary solver to Astrometry local and it works perfectly ?????? David.

I bought one recently just for a giggle really but I have to say I am really quite impressed with it. With reasonable polar alignment and a Canon 70D with a 200mm prime lens I can get 40 seconds unguided with reasonably trail free images. Its really good fun!! I can also use it set at 90 degrees for slow scanning time lapse! I would suggest its a good intro to imaging without spending much money.

Thanks Frank - that's extremely helpful.

When I set up my Mesu 200 I followed the instructions to the letter and part of that was using Carte du Ciel I have tried to love CdC but I cant - I still much prefer Stellarium. CdC works brilliantly with the Mesu but its not for me. I understand that the latest versions of Stellarium do not require the use of Stellarium Scope as a separate programme. So last night the seeing was dire so I tried to connect Stellarium to my Mesu. I got the Configuration - Telescope control and despite trying every combination of the connection options I could get it to work. Out of curiosity I downloaded Stellarium Scope and it connected first time ! Any suggestions anyone??? I am using Stellarium v0.19.1

When you say 'tightened all the tolerances up' you might have introduced some binding?? This guide is excellent and if followed exactly will leave you with a properly functioning mount. http://www.astro-baby.com/heq5-rebuild/heq5-m1.htm If you get stuck - shout out. If you were nearer I would gladly show you how to fettle it.

Thank you! I am trying to develop a lighter touch in my processing rather than my usual cack handed 'whack up the saturation' - 'smack in the face' results.

The Elephants Trunk Complex (IC1396) - Takahashi 106 EDXVi, Atik 16200, Atik EFW3 filter wheel, Baader 2" narrowband filters, Mesu 200 mount guided with SW ED72 and ASI 290 mono. Software - SGP, PHD2, processed In Pixinsight and fully calibrated with darks, bias and flats. 3 hours Ha - 2 hours Oiii and 2 hours Sii all binned 1x1 - Processed in Hubble pallet using Pixinsight. Very poor seeing and 72% moon. Hi res version here - https://www.flickr.com/photos/113316085@N05/49083911368/in/album-72157675109735132/

Very sad - I was only speaking with him the other day - he used some of my images in his recent book 'Oor Big Braw Cosmos'. A very nice chap and a real 'old school' gentleman' My sincere condolences to his family. R.I.P.

+1