Gina

I've found :- 4 350Ds - 3 with sensors 2 1000Ds - one complete with screws so probably sensor too - the other without screws so don't know ATM Another - innards only, could be 1000D - takes same battery

I have various other camera models that I can debayer, I think, so I might have a play with those - all good fun I'll see what I can find. I have bought 300D, 350D, 450D, 1000D and 1100D models. Trouble is, some are in bits and I may have a problem working out which bits go with which Actually, some more practice on other sensors would be a help before I go further with the 1100D one, now that I have more facilities.

Yep

Thanks for that and welcome back Luis You're certainly right about the 1100D - not just the CFA but the cover glass is super-stuck on - with a vengeance!

Um... I see no ships... I mean images....

Good thinking Mono CCD cameras are great and more sensitive than DSLRs though the image sensor is often smaller, depending on how much you pay. We who are doing this debayering project are dedicated DIY nuts (or machochists) - with apologies to the others - I'm really just speaking for myself I'm an addict for difficult projects When you save up enough I can definitely recommend Atik mono CCD cameras. eg. the 460EX is very low noise and one of the best.

I use some thin, hard plastic to keep the cold finger away from those tiny SMDs. This was from offcuts from secondary double glasing sheet but any thin, hard plastic will do. I made a T shaped piece so that the lugs stuck out beyond the gap and stopped the plastic sliding in too far when inserting the CF. Plastic in first then CF between plastic and sensor with thermal paste on the CF. The SMDs and plastic insulation limit the thickness of copper sheet for the CF - I used 0.7mm. In spite of the thin copper I managed to get the get the temperature down to -15C with an ambient of +14C.

I've edited the post to show the photos. NO don't file them off

Thank you Russel I already have a photo of the sensor side of the imaging board I think. I can tell you that that what looks like pins are actually tiny SMDs tiny little capacitors or resistors at a guess. If I can't find the photo I'll strip down an 1100D sensor assembly and take another. Happy to oblige Later... Found the photos

Next will be the epoxy potting resin I shall practice on a duff sensor first before tackling this one. I'll add the resin and let it cure before cleaning the muck off the sensor. Then we get to the interesting part

Cover glass photos at different angles.

The cover glass on the 450D comes off easily with an Exacto knife or similar - no heat required

Images from sensor - flat and view through living room window.

Put some insulation tape over the sensor and on the glass. Tried the hot knife - no joy, just turned the glue black where I had gouged out bits that showed white! Then attacked it with an Exacto knife. Another couple of bits of glass broke off - absolutely no sign of it shifting over most of that edge There is now a strip of glass remaining along that edge and the sensor is now clear. In spite of all the precautions, there is some damage to the sensor surface. I think the chances of getting the last of the glass off is negligible Next I put the filters back onto the sensor unit (to avoid any more damage), put it back into the camera and reassembled the camera for testing. The good news - the sensor still works. The bad news - two bright magenta horizontal lines and one black vertical line The glass also pulled the sticky tape down onto the middle of the sensor leaving a sticky patch but I imagine I shall be able to get that off with IPA. I'm not going to try any more to remove the rest of the glass. If I don't succeed in totally destroying the sensor in debayering I shall have to build up the frame to the level of the remaining cover glass before putting one of my spare cover glasses on to seal it. The remaining glass is clear of the imaging area. I'll take and post some pics shortly

I'm not going to risk the gas flame on it any more. May try hot knife-edge. I had the torch on it's lowest setting. I guess I must have applied too much heat trying to get that last bit of glue to turn white That was when the glass cracked and flew off.

Ah, I see

I have a blade in the Dremel blowtorch kit so I guess I could try that

They've brought their prices down since I last looked I agree that's not a bad price

I wonder if they have a number of failures and that's why they charge a lot for the finished camera and take a long time

Thank you Louise Yes, that's the method I've been using, pretty much. Glad you're debayering is done

OK - yer tis In case of confusion with my earlier postes, the RHS of this photo was at the top when I was heating the cover glass.

Might be an idea to put some adhesive tape over the exposed sensor and wires and also on the remaining glass so that it doesn't drop onto the wires or sensor. I'm giving it a rest for a bit while I gather my thoughts. And allow time for any suggestions anyone might have

Thanks Russel I think the last bit is going to be difficult - and that's an understatement!! The top seems to be very securely glued on. I started carefully lifting where there was some white but with another ping, a small bit flew off! Fortunately, well clearing the sensor - I think it landed on the floor. We are now up to a totally glued area. At the other end the glue has gone and the glass to frame area is showing moire fringes. If I apply too much pressure the corner will fly off I don't think heat is an option - I've already applied a lot of heat to that area and I don't know how to apply more heat without risking cooking the sensor or gold wires. TBH I don't know what to do next. I knew the glue wanted loosening all the way round and after the rest went I concentrated on the top bit but still very carefully as in your video. In spite of cooling the frame was hot - probably 70-80C going by touch.

Another day - another attack on a sensor I decided NOT to use the cold finger but to cool the frame and metal shield - only slightly. I used Russel's method and almost immediately I got white showing at the bottom. I continued carefully flicking the flame over the glass and the whiteness spread all across the bottom and up the sides but the top just would not turn white. After a couple of minutes of careful heating there was a "ping" and two thirds of the glass from the bottom flew off. I stopped at that stage and tried to prise off the rest of the glass without success. So being aware that the part of the sensor and gold wires were now exposed, I put the filter frame back and put the sensor back in the camera for testing. It still works

No, I think the heat just destroys the epoxy.