Mav359 Posted April 13, 2015 Share Posted April 13, 2015 No real need i suppose but why not Started to build an auto focuser for my MAK, the optics are great but you only need to look at the mount and the thing shakes all over the place so i figured if i can focus away from the scope then all the better. Its mainly for visual but i intend to a bit of planetary, solar and moon pics with it. I'm going to get ant EQ5 for it i thinkNothing fancy Easy stepper and nano wired together, i have headed the boards and mounted it all in a project box... simples. The only thing extra i do is wire the easy stepper up to a RJ11 port & one at the motor end, that way i can use a single cable from the motor down to the control box. Motor is here and the RJ11 port has been soldered to the motor cable. Control box done.Awaiting the pulleys to arrive and then once they are mounted i can work out exactly where the motor box will sit and the pitch between the pulleys and can then order the belt.Just a repeat essentially of what i did for my SCT. Link to comment Share on other sites More sharing options...
nightfisher Posted April 19, 2015 Share Posted April 19, 2015 Any progress on this project? Link to comment Share on other sites More sharing options...
Mav359 Posted May 6, 2015 Author Share Posted May 6, 2015 Hi JulesBeen busy and waiting on parts but finally made progress today.Ally plate arrived and ive cut it out & the pulleys are here.Im using the visual back as part of the attachment mount, only thing is because of the plate it doesnt quite lock the visual back in place so an O' Ring is going to be required. Have measured the pitch between the Pulleys as 80mm so i can get the belts ordered now. As i said a variant on my SCT AF but i'm quite please, few screws here and there i need to replace and im going to put a velcro backing between the OTA and the back of the project box as another means of securing the housing in place.They were the biggest and smallest pulleys i could use so the gear ratio is only 2.4:1 but its better then none at all. Once i map the movment of the motor i can work out the steps required and the speed at which to use the AFappriciate any thoughts and comments Link to comment Share on other sites More sharing options...
Mav359 Posted May 12, 2015 Author Share Posted May 12, 2015 Well it works but inevitably there is a small issue.... 3mm small in factThe motor pulley and focuser came in with a pitch between them of 80mm, unfortunately the closest cross morse could get with the belt was 83mm so its slightly too big....... tutEasy enough fix my ally plate was 180mm long so im going to re-order that and use the first attempt as my template for the Visual back & focuser cuts. The motor box will move to the end of the new bar pick up the 3mm and all will be well in my world :-)As it is its perfectly useable it deffo can't come off, there is some very occasionaly slipage but its actually fine. I could leave but my OCD is kicking in and the statement "That Won't Do" keeps ringing in my earsCouple of other things to do is to secure the motor box to the OTA but that will have to wait now until the new plate arrives and i can seat the box. The other thing is a few washers/o-rings to lock the visual back a bit moreCheers Link to comment Share on other sites More sharing options...
nightfisher Posted May 12, 2015 Share Posted May 12, 2015 Looking very good, where did you get the ally plate, i need a piece to do my 150 mak focuser Link to comment Share on other sites More sharing options...
Mav359 Posted May 12, 2015 Author Share Posted May 12, 2015 Looking very good, where did you get the ally plate, i need a piece to do my 150 mak focuserClick Metalhttp://www.clickmetal.co.uk/Angle-Types/Sheet-and-Plate/Aluminium-Sheet-1mm---5mm/p-16-6-22/?x=x&plateID=337&vp=25.48&vcpu=2.4&vcpo=0.8&vgrade=1050Love this place Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.