Adrian Celija

Many thanks I will find out and let you know so we can be sure.

You mean to have USB type B on faceplate and regluar USB type A on other side of cable to connect the mount and pc for ascom ?

Julian thanks for answer, I finally found what is broken........take a look at regulator, it has a small crater........

Julian hi, Thanks for everything but looks like my mobo is gone. I will order a new one.....I tried everything I could, trying to find if mobo doesn't have power on molex, regulator and all stuff I could, like motor connection, and voltage on connection, voltage on HC connection etc.....everything looks fine but I noticed a little smell once I opened mobo, that particular smell of electronics. it means nothing but could be symptom of something dead on mobo. I can get az eq6 R mobo with its faceplate. will let you know once I get it and replace it.

Julian thanks, few minutes ago I connected without a problem pc/ascom with eq3.....but through pc direct mode....one question, link that you gave me for the driver for eqidrect few post above is this one: "PL2303_DriverInstaller_v1180_20170406".......but I can not find it for downlload, please can you give me link for downlload? Just want to make sure that I tried every possible solution before I order FTDI eqdirect

Than I am in big problem, I can not use my mount, no way to fix it untill that situatuon with virus calms down, btw, have you ever tried to connect eq3 on pc via ascom connection?

So that was mine concern, if that is so, I can not use V4 for small alt/az on eq6 although is working?

Many thanks for reply, for some reason v3 HC is not working on eq6 but the same cable the same v3 HC works without problem on eq3........that is what confuse me............on the other side, if something is wrong with the motherborard (conection, power etc) on eq6, than even v4 wouldn't work...........but it is working normally on eq6............very strange..........however there is one thing, now I can not even connect to pc/ascom via "pc direct mode" selected on working v4 HC.............I get two messages. "connect error port not available" or connect error "timeout" ................I am completely frustrated.......

I managed to connect mount with pc only first time, via "pc direct mode" set on handset and rs232 with usb adaptor for rs232. I have also Prolific "HITEECASTRO" eqdirect cable(rj45/usb) but never manage to connect it. After disconecting form first successul atempt everything went wrong and can not get rid of that message on HC.......both axis no response..........

no advice any more?

Logic says that cable is ok if mount is working with V4 handset, but of course I can not be sure. I have two cables and both tried and same thing occured, then I test both of them on eq3 with "problem handset V3" and both respond normally as well as V3 handset. Is there any kind of reset of motherboard? Al this problems started after I disconect handset from PC, maybe motherboard or even handset stucked in some kind of boot or loop- not an expert just thinking out loud

I tried today one more thing...............I start the mount with the wifi synscan anb mobile aplication and worked normally. Only with the v3 handset I can not go further.......

Peter just output voltage, no load, I can not move motors with the handset which gives me mesagge " caution......both axes no response". Kev, once you turn on power, first is initilaizing, after that if everything is ok, handset goes in mode to ask you if you want to go in eq or az mode. I do not get there, only that stupid message.

Ok I got the measurments, so output voltage on cable is between 12.46-12.54V, voltage on handset says 12.3V. So handset measure 0.16-0.24 V less. What now? Thanks

Thank Peter, as soon as I measure output voltage from cable I will report here, then we will know if power or handset need fixing.

Peter, Thanks for quick reply. I will try to check the voltage latter when I get the multimeter, I escaped to village due to virus so I will not be able to check it i next few hours untill I get it. Can you give me the name of that special firmware or a link? I will try to do it with first one that gave me this message. many thanks

Hello, I own SW AZ eq6 gt, SW eq3 and SW alt/az goto. Everything was fine with my eq6 and working properly. Few days before, I decided to try connect eq6 via Eqdirect/ascom/eqascom to my laptop, but my laptop couldn't recognize it, although I checed houndred of times COM port etc. Then I decided to try to connect it via RS232 and V3 HC and "PC DIRECT MODE" and I succeded, used stellarium and everythying looks promising. Later I tried to conect it again to see how to set up PHD2 but I couldn't do it. After I shut dowm the power of eq6 and tride and power it again, without conection to laptop I got message "CAUTON....BOTH AXIS NO RESPONSE". I tried several times to start it normaly but no success. I changed the power adapter, tried to put in on power tank etc and nothing happen. However I could enter in V3 HC menu and read voltage and it was 12.2V. Then I decided to try V3 HC from eq3 and same message same voltage 12.2V. Then I tried V4 HC from small alt/az mount and eq6 was working normally, although voltage in V4 was 8.4V. My conclusion was that both V3 HC are broken for some reason. "But how can that happen that both of them are gone at same time"? I was suspicious..... maybe V3 HC are ok......? Next day I decided to try both V3 HC on eq3 and guess what, they were working normally. I tried again them on eq6 but same thing "both axis no response". The only thing that I didn't change in all those trying and testing was power cable that connect mount and power adapter, because I have only one. Picture in attachment. Also when tried to connect to ASCOM with rs232/HC and "PC DIRECT MODE" I got message "connect error....Timeout". Tutorial which I used to setup ASCOM conection says that this message comes if there is no power on insuficent power. So I suspect that power cable for some reason doesn't provide more than 12.2V and that HC V4 don't need more than 8.4V.???? Maybe just maybe..... To make thing more clear for advices I also put last firmwares in both V3. So they are updated. Any ideas on what is going on? Many Thanks Adrian