Jump to content

Stargazers Lounge Uses Cookies

Like most websites, SGL uses cookies in order to deliver a secure, personalised service, to provide social media functions and to analyse our traffic. Continued use of SGL indicates your acceptance of our cookie policy.

Max Todas

NEED HELP! Can't identify my telescope brand

Recommended Posts

I have a telescope that I received from a teacher. I know it's a celestron but I can't find any info on the model/type, and I can't find the name of the telescope anywhere on it. Can you tell me what type of it and if I need the electrical parts to make if work?
Here's a link to a photo of it. 

 

https://photos.app.goo.gl/ZtBm1pe1fTszG9FQ8

 

I don't have a manual for it as I don't know the model so I can't figure out how and what I need to fix it, or make it work(if it's missing a specific piece or something) I need to know what model it is so I can find the pieces for it and learn what it needs to work. 

IMG_20200724_131543.jpg

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Zermelo
      The focuser on my SkyWatcher 150i is a basic rack-and-pinion, unsurprising for the price point, but sometimes a bit of a pain to control finely enough. I’m not looking to spend any serious money upgrading it, but I did want to see what I could tweak.

      The first thing I did was to slacken off (slightly) the screws holding the plate against the spindle, as the operation was very tight when new – that helped a bit (and I think that without doing this first, the “friction fit” approach described below wouldn’t have worked). I will eventually get around to taking it all off as per AstroBaby's tune-up.

      Improving the fine control without a major change means doing something with the focusing knobs – they’re quite small, so the effective “gearing ratio” when you operate them is on the harsh side. Some folk have described fitting larger diameter replacements, either bought or made, and even using ones with a planetary-style mechanism to achieve a reduction in the ratio. I didn’t fancy this, as I couldn’t see how the existing knobs were attached to the spindle without trying to prise them apart (possibly terminally). The other option is to increase the effective diameter of the existing knobs, for which purpose a clothes peg is apparently quite popular, but I’ve also come across descriptions of chop sticks inserted into holes drilled at intervals into the circumference, and punctured lids from peanut butter jars.

      I wanted something that was cheap, relatively tidy and non-destructive. The answer seemed to be some sort of thick sleeve that I could fit over the knob. It would need to be a tight fit so as not to slip in use, to be not so large as to foul against either the focuser tube or the main OTA, and to be thick enough that it didn’t flex sideways when grasped. I thought I might find some larger rubber washers that would do the job, but none were thick enough to be rigid in use. However, a bit of searching found these spacers that are apparently used in vehicle shock absorbers.

      My calipers said the diameter of the focuser knobs was around 29.5mm, and the nearest spacers that were available had an internal hole 30mm and outside diameter 60mm. I ordered one that was 10mm thick, not quite as deep as the knobs, but which allowed a bit more space on the inside edge for free operation. I’d hoped the internal hole might be a but undersized when it arrived but it was spot on, so I wound five or six turns of masking tape around the knob first. To avoid taking the tape off when fitting the spacer, I positioned one side first and stretched it across the face as I pushed. When it’s flush with the knob’s outer face, it’s just clear of the focuser body and OTA. There might be enough room to stick some kind of friction surface around the outside to improve the grip, but I don’t think it’s going to be necessary.

      I decided to do only the one knob, so I now have a very Noddy “dual speed” affair.  Because the clearances around the fitted spacer are quite tight, it’s worth checking the positioning of the spindle in the focuser body first – mine was fractionally off centre, so there was more room one side than the other (assuming you have no preference).



       



       

       
       
       
       
       
    • By Spacecake2
      Hello,
      I know you've seen these questions a lot (unless your new) but I'm struggling a lot on if I should buy a Skywatcher 250px (10") or 200px (8") (dobsonians). I have a 5 inch and i'm looking for a big step up for noticeable changes. 
      Thank you 
       
    • By Spacecake2
      What telescope brand would you choose?
      Reply below for your favourite telescope brand. It would be really helpful to know which brand to buy.
      Celestron, Meade, Orion, Skywatcher  etc.  
      Thank you for viewing
       
    • By GiL Young
      Hello, all ~
      If you'd please take a moment to read the info in my profile, I'd be grateful beyond words. In short,, I leaped into this new passion before fully researching all of it's necessary aspects. I'm determined to verify with my own eyes the deep cosmos and better understand the far past & distant future events. Thanks so much for indulging this newbie.
      ~ GiL Young
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.