Jump to content

Stargazers Lounge Uses Cookies

Like most websites, SGL uses cookies in order to deliver a secure, personalised service, to provide social media functions and to analyse our traffic. Continued use of SGL indicates your acceptance of our cookie policy.

sgl_imaging_challenge_banner_beauty_night_skies.thumb.jpg.2711ade15e31d01524e7dc52d15c4217.jpg

Chriske

Building/printing Hubble telescope scale 1:7

Recommended Posts

SaturnV (x4) scale 1:55 are done.

This time our director asked me to build a scale model of Hubble space telescope to be hung just above the entrance of our planetarium.
I actually will build two versions. One is 1:7 and the second will be 1:10 scale
Busy making the two tubes of the largest one. One is 600mm diameter and the other is only 420mm diameter.
Total length of that 1:7 scale model (open-door included) will be about 2.3meter.
In both cases only a few parts of the models will be printed.

Is there a specialist Hubble space telescope out there...??? I have a few questions about Hubble.
This is were I have most of the info from.

Zoomed in on the back of Hubble I see a few(4) vent-holes. Why are there vent holes at the back..in space..?


image.thumb.jpeg.5012cb040a18ae3893212ff0eb74e0d0.jpeg

image.jpeg.5de0d88c228be6f6f44de9d907a1fbb9.jpeg

image.jpeg.2d4b208394b2897260d63521b1ee4759.jpeg

A few more questions yet to come, thanks..!

  • Like 2

Share this post


Link to post
Share on other sites

WOW!!  YOU sure go in for BIG projects Chris!  :thumbsup:

  • Haha 1

Share this post


Link to post
Share on other sites

All four tubes for this project will be made of hardboard 3.6mm thick.

During course, along time ago  before we started using trusses, we made our telescope tubes out of cardboard too.
In the beginning we used PVC tubes which were very heavy. In fact to heavy when we started building larger scopes. So we made our tubes out of cardboard instead.
Before we wrapped the cardboard sheets around a PVC tube we sprayed them soaking wet. Then we started bending the wet cardboard very slowly around a PVC tube and fastened the cardboard with buckles. These cardboard tubes are very light, strong and cost a fraction of the same size PVC tubes.

At he outside these cardboard tubes are very smooth and at the inside you have that nice rippled surface. Ideal in combination with black paint to flock the inside.

  • Like 1

Share this post


Link to post
Share on other sites

In the past many things were made out of papier-mâché - wet paper and flour paste, and were very strong.  So I can see a similar composition being strong and light for telescope tubes.

Share this post


Link to post
Share on other sites

Oops...!

Need to correct something here.
Higher up I said we made telescope tubes out of cardboard back then. That's pure nonsense of course..:laugh2:
That should have been hardboard of course and not cardboard... silly me..!

  • Haha 1

Share this post


Link to post
Share on other sites

I gather papier-mâché can be as strong as wood.

Share this post


Link to post
Share on other sites
9 hours ago, Chriske said:


Is there a specialist Hubble space telescope out there...??? I have a few questions about Hubble.
This is were I have most of the info from.

Zoomed in on the back of Hubble I see a few(4) vent-holes. Why are there vent holes at the back..in space..?

A few more questions yet to come, thanks..!

Chris would one on those Haynes Manuals be useful, I believe there is one on the Hubble.

Haynes Manual - Hubble

Jim 

Share this post


Link to post
Share on other sites
3 minutes ago, saac said:

Chris would one on those Haynes Manuals be useful, I believe there is one on the Hubble.

Haynes Manual - Hubble

Jim 

Hey, thanks a lot for the tip..!:thumbsup:

Share this post


Link to post
Share on other sites

I did but it's a bit small compared with what I'm planning to build.

Maybe I did miss something..?

Share this post


Link to post
Share on other sites

Something I might be interested in though.  I might consider making a smaller version than Chris but I have many projects on the books before I could get to that.

Share this post


Link to post
Share on other sites

This is a very good site, many detailed views, but no explanations or measurements, pity.
On that other site there are some measurements. It's probably enough for my project.

Share this post


Link to post
Share on other sites

What are these 'Scuff plates' for..?

image.png.15dd774214b6a7034df02366bbb2f621.png

There are four of them.
I'm only guessing here : four devices to firmly hold Hubble in the the Shuttles cargo-bay during transport..?

image.jpeg.f488b467595a887254be33279bdf0b2b.jpeg

Share this post


Link to post
Share on other sites
2 hours ago, Chriske said:

What did you have in mind, how small..?

Haven't really thought.  Maybe something I can print on my Giant 3D printer when I've got that working again.  Even that is sometime in the future after I finish my ASC, ROR automation and a couple of other things.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.