Jump to content

sgl_imaging_challenge_banner_31.thumb.jpg.b7a41d6a0fa4e315f57ea3e240acf140.jpg

Recommended Posts

Hi guys,

I been googling a lot and was not able to find a solution how to connect EQMOD to the Mount via SW Wifi Dongle...

it looks like EQMOD needs COM Port to be used....

I do remember there was some kind of "Virtual Com port bridge to Wifi"app back in Win98 days... But I cannot find anything similar for Win10.

I want to test EQMOD auto-guiding via WIFI, - I know, it's not reliable, but I want to try

as I have Skywatcher wifi dongle and my USB to Serial (RS-232) Converter Cable is wayyyy too short to keep my PC (and me) in warm.

I am able to connect with SynScanPro app to Wifi Dongle and even sync it with Stellarium nicely... 

Only Auto-guiding missing...

Any ideas?

 

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Ade Turner
      I’ve just bought a Skywatcher EQ6-R Pro. I’m trying to drive it from Stellarium using EQMOD but I’m running into a problem I haven’t the experience to solve.
      This is my set up:
      Windows 7 Laptop > 10m active USB 3.0 cable > 4 port powered Atolla USB 3.0 hub > Lynx Astro EQMOD cable > Mount (plugged directly into hand control socket)
      When I first connected the mount to the laptop (a 2015 Dell Inspiron) Windows 7 searched for a serial/USB driver and installed it on COM 8 (according to Device Manager).
      In Stellarium I created a profile for the mount but it wouldn’t autodetect the COM port. So I manually set it to 8.
      When I try to connect to the mount it sits for a while and then tells me the connection has timed out.
      Anyone have any suggestions as to where I should start to try and get the connection sorted please? Thanks.
    • By Arshad Wali Muhammad
      Hi. I have Celestron CPC 1100 EdgeHD with Starsense and WiFi Module. During the alignment process, WiFi module stops responding, whereas my tablet or iPhone is connected to the WiFi module,  the SkyPortal message pops up that connection is failed and scope isn’t responding? Can anyone help me how t fix this urgently ? It was working fine yesterday but now I can see this message. I though it’s a power issue, so I disconnected the power tank and connected the scope directly to the electricity through supplied adapter, but failed. 


    • By laks20
      Hello 
      I have a telescope -SkyWatcher Explorer-130P SupaTrak Newtonian Reflector auto Telescope  and it has a  heavy duty tracking device ( pic attached). I have had this scope for a few years and did pretty much basic with this and never understood how to use this device. I have the time now to spend with the scope during this social distancing time and I am totally unaware of how to efficiently use the tracking. I know how to move up, down, left and right. I don't think it has wifi and it looks very basic ...please can someone explain how to set this up. Pleaseeeeee can someone help .......I have searched everywhere but I can't find any material on this.
      Also , If i buy SynScan ( with wifi ) will it work with my scope? Thanks in advance xx


    • By morayskies
      Hi All
      Has anybody else had this problem?
      I use a single, ageing laptop (HP620 8Gb RAM) running Windows 7 Pro 64bit to control my imaging setup using the following software;
      Cartes du Ciel and EQMOD to control EQ5 Pro mount via EQDIRECT cable connected via powered USB Hub
      BackyardEOS to capture images from Canon 450D via same USB powered hub
      PHD2 for guiding using GP-CAM 130C and EQMOD pulse guiding
      What confuses me is that some evenings everything works absolutely fine.  Another evening, using exactly the same hardware, software and even connections (ie I always plug the leads into the same ports) the system will be working fine but then suddenly fail.  The failure affects EQMOD indicating a timeout or port not available issue and the Canon 450D also 'locks' requiring a restart of the camera and BackyardEOS.
      I have run USBTree during such a failure and it is showing that the EQDIRECT cable (ie serial converter) is still connected to COM4 (which is correct) and the Canon 450D is also still connected.  I basically have to ensure that all the software is closed and any associated services also stopped.  Of course, the scope is now pointing away from its home position so I have to move it manually back to 'home' before starting again.
      My thoughts are that there could be a number of issues;
      1. Use of a USB hub
      2. A dodgy EQDIRECT cable
      3. USB cables too long (ie about 5m)
      4. Windows is turning off a connection (I have set the power management for each USB port to 'off')
      5. Canon 450D somehow 'freezing'

      When using this laptop, I turn off the Wifi and Anti Virus and Automatic Updates are also off.
      It just baffles me that sometimes this system works flawlessly for hours and yet other nights it keeps failing.
      Any suggestions gratefully received.
      Thanks for looking.
    • By astrosathya
      Starting my 1st IOT project. Since i've been an astrophotographer with no permanent setup, it makes sense to reduce the physical footprint (and the weight) of as many equipment as possible, as well as to do better cable management. I am soon going to start using Astroberry Pi server, an Ubuntu based suite for Astrophotography. Just purchased a Raspberry Pi 3B along with a 3.5" display for that. Lets see how it goes.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. By using this site, you agree to our Terms of Use.