Jump to content

sgl_imaging_challenge_2021_2.thumb.jpg.72789c04780d7659f5b63ea05534a956.jpg

Controlling a Losmandy G11 mount with Eqmod


Recommended Posts

Hi all,

Before turning to AZ-EQ6 GT mount, I tried to upgrade my previous Losmandy G11 mount to autoguiding by use of a SBIG Relay Box connecting the PC to the mount through an ST4 cable. I didn't intend to transform it into a goto system -it remained manual- just wanted to realize an autoguided system, and I succeded for short exposures up to two-three minutes, but I wasn't able to scale up, hence I turned to the SkyWatcher. My Losmandy dates back to the end of 1990's, but never showed backlash and worm-gear play like the brand new AZ-EQ6 GT did. I was quite deluded by that, and I still complain and dream to realize a G11 full upgrade to a goto system. Now I wonder whether Eqmod ASCOM would make it, maybe just by controlling the Relay Box/ST4 connection through Eqmod. May somebody give me an answer? I would also like to get comments on the idea of a full upgrade of the G11: is it worthy of that? If positive, I would also like to explore more complex systems for the full upgrade, given that anybody has an idea.

Cesco

Link to post
Share on other sites

Hello from Vienna,

To upgrade your Losmandy G11 to a modern GoTO mount, there are few possible options..

1, to contact Losmandy directly, just google for it, Losmandy has all modern spare parts you can exchange as upgraede for your Losmandy G11, they could even give you ideas ?.

2, have a look to this thresd.. https://www.cloudynights.com/topic/458457-new-avalon-stargo-drive-system-for-losmandy-mounts/ also an interesting upgrade.

3, do what I did, as I did have a losmandy, G11, did upgrade with ESCAP motors + FS2 controller.. all needed parts could be ordered from Here

4, finally you can also order from here the parts to make out of your Losmandy a GOTO Losmandy, look Here

For every hardware you decide for, there is an own software solution available to control it remotely and to cohtrol GOTO and guiding also         " since you did mention in your thread EQMOD "

The good fact about Losmandy is, almost all parts are exchangeable and upgrades are possible., though the upgrades are expensive.. $$$$$$

Good luck

Martin

 

 

Edited by Guest
Link to post
Share on other sites
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Ade Turner
      I’ve just bought a Skywatcher EQ6-R Pro. I’m trying to drive it from Stellarium using EQMOD but I’m running into a problem I haven’t the experience to solve.
      This is my set up:
      Windows 7 Laptop > 10m active USB 3.0 cable > 4 port powered Atolla USB 3.0 hub > Lynx Astro EQMOD cable > Mount (plugged directly into hand control socket)
      When I first connected the mount to the laptop (a 2015 Dell Inspiron) Windows 7 searched for a serial/USB driver and installed it on COM 8 (according to Device Manager).
      In Stellarium I created a profile for the mount but it wouldn’t autodetect the COM port. So I manually set it to 8.
      When I try to connect to the mount it sits for a while and then tells me the connection has timed out.
      Anyone have any suggestions as to where I should start to try and get the connection sorted please? Thanks.
    • By morayskies
      Hi All
      Has anybody else had this problem?
      I use a single, ageing laptop (HP620 8Gb RAM) running Windows 7 Pro 64bit to control my imaging setup using the following software;
      Cartes du Ciel and EQMOD to control EQ5 Pro mount via EQDIRECT cable connected via powered USB Hub
      BackyardEOS to capture images from Canon 450D via same USB powered hub
      PHD2 for guiding using GP-CAM 130C and EQMOD pulse guiding
      What confuses me is that some evenings everything works absolutely fine.  Another evening, using exactly the same hardware, software and even connections (ie I always plug the leads into the same ports) the system will be working fine but then suddenly fail.  The failure affects EQMOD indicating a timeout or port not available issue and the Canon 450D also 'locks' requiring a restart of the camera and BackyardEOS.
      I have run USBTree during such a failure and it is showing that the EQDIRECT cable (ie serial converter) is still connected to COM4 (which is correct) and the Canon 450D is also still connected.  I basically have to ensure that all the software is closed and any associated services also stopped.  Of course, the scope is now pointing away from its home position so I have to move it manually back to 'home' before starting again.
      My thoughts are that there could be a number of issues;
      1. Use of a USB hub
      2. A dodgy EQDIRECT cable
      3. USB cables too long (ie about 5m)
      4. Windows is turning off a connection (I have set the power management for each USB port to 'off')
      5. Canon 450D somehow 'freezing'

      When using this laptop, I turn off the Wifi and Anti Virus and Automatic Updates are also off.
      It just baffles me that sometimes this system works flawlessly for hours and yet other nights it keeps failing.
      Any suggestions gratefully received.
      Thanks for looking.
    • By Demonperformer
      I am at a complete loss to understand why eqmod was not syncing on CdC last night. I have had a look at this video, I had the star centred on the screen [3m33s], I pressed sync on CdC, I got the dialog box [3m39s], I clicked 'yes' and NOTHING happened: the white circle stayed where it was, no sync points were added to EQMOD, zilch!
      I can get round most problems, but this really one stymies my GOTOs and, therefore, my imaging process.
      I have been unable to find anything in the EQMOD documentation that deals with such an error and a search on here has turned up no help (but that always depends on the words put into the search!). I checked all the obvious things (location, date/time, etc - but why any of these should stop sync working is beyond me). It's all running on Windoze 10.
      Any suggestions on why this should have stopped working and (more importantly) how I might get it working?
      Thanks.
    • By Demonperformer
      Setting up all the software on my win10 laptop and getting things to talk to one another is a nightmare.
      I'm starting a new thread, so I can post all the problems I am having, one at a time, so issues don't get confused. This will also hopefully help anyone coming to similar situations later, as the problems and answers will not be interlaced.
      First issue: APT does not detect ZWO camera.
      I have got the camera (ZWO) drivers installed and sharpcap can see it and will connect to it properly. However, when I try to connect the camera in APT, the only CCD options it gives me are SBIG (which it isn't), QSI (which it isn't) and ASCOM. Now it shouldn't need to use an ascom driver, because the proper driver is installed, but I give it a go anyway, and this just offers me 2 simulators and 3 QHY cameras (I have one qhy driver installed for the guidecam .... I'll get to that later!). I have disconnected both the filterwheel and guide camera from the camera hub, so they cannot be interefering with the process.
      I am at a total loss ... any suggestions?
      Thanks.
    • By RolandKol
      Hi guys,
      I been googling a lot and was not able to find a solution how to connect EQMOD to the Mount via SW Wifi Dongle...
      it looks like EQMOD needs COM Port to be used....
      I do remember there was some kind of "Virtual Com port bridge to Wifi"app back in Win98 days... But I cannot find anything similar for Win10.
      I want to test EQMOD auto-guiding via WIFI, - I know, it's not reliable, but I want to try
      as I have Skywatcher wifi dongle and my USB to Serial (RS-232) Converter Cable is wayyyy too short to keep my PC (and me) in warm.
      I am able to connect with SynScanPro app to Wifi Dongle and even sync it with Stellarium nicely... 
      Only Auto-guiding missing...
      Any ideas?
       
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. By using this site, you agree to our Terms of Use.