Jump to content

stargazine_ep44_banner.thumb.jpg.6153c4d39ed5a64b7d8af2d3d6061f61.jpg

Manfrotto 02b 02B Heavy Duty Camera Tripod


Recommended Posts

Manfrotto 02b 02B Heavy Duty Camera Tripod. heavy duty ideal for astrotrac style imaging or heavy binoculars.

£100 cash on collection from Ledbury only as i have no box to ship it in

s-l1600.jpg

s-l1600 (1).jpg

Link to post
Share on other sites
  • 4 weeks later...
  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By andyrawlins
      Hi All
      After much research, primarily on this site and The Binocular Sky, I got hold of the above binoculars.  I spent ages writing a review specifically for this site of what I found, as a thanks for all the advice I had received.  By the power of idiocy I then managed to post it on Cloudy Nights instead (I had both open in my browser).  Too much Christmas port I guess  
      Anyway, too late to take it down as some have already replied and I guess I shouldn't post the same thing on two sites so here is a link to my review on completely the wrong site   No offence at all to Cloudy Nights but I wrote it with the Stargazers Lounge audience in mind and it may make less sense on a US site.
      Comparison of Pentax SP 50 WP 10x50 and Nikon Action EX 10x50 CF




    • By Zermelo
      I saw a suggestion somewhere (possibly in SGL) to attach lights to your tripod legs (dark-adaption-friendly ones, of course). The idea being to avoid accidental collisions, especially at star parties or outreach events. We experience this quite regularly at home too, so I decided it was worth pursuing (and also, as users of go-to functionality, I’m getting tired of repeating alignment operations throughout the evening).

      The very simple idea was a (removable) clip for each leg, each with an LED. I briefly considered a self-contained battery to power each, but decided that charging them was too much hassle (and I also doubted finding LEDs that would operate at such low voltage). Instead, they would be fed from the USB port on the power supply I previously rigged up. I thought the LEDs would be more noticeable if flashing, and found these.

      My SkyWatcher 150i tripod has 1.25” upper legs and 1” lower. Since collisions are most likely with the lower legs, it was that diameter I worked with. I looked for plastic pipe clips of this size (the most common ones are 15mm and 22mm used for plumbing) and found these. They have a hole for a fixing screw that can be used to hold an LED, and they have a hinged collar for holding the tube, which preserves a gap that allows electrical connections to pass.

      The screw hole in the clip was wide enough to admit the LED body but not the rim. To allow the LED to protrude from the clip I drilled out the holes a little wider, and about 2/3 of the distance through the clip. The LED could then be pushed through until the rim engaged, and the terminal leads were bent into a succession of right angles to guide them to the top of the clip. I found some twin speaker wire in my junk box, and soldered lengths to each LED’s terminals. The clips have a channel along the edge to allow them to be ganged together. I opened them out with a needle file so that the speaker wire was a tight fit when pressed in – this was for strain relief.

      I covered over the soldered joints with some scrap plastic strip, screwed into the clip, and pushed some Araldite into the hole and around the exposed metal, to prevent shorting:

       
      These LEDs seem to work on 5.1V without needing a series resistor, so I twisted the positive and negative ends of the three speaker cables to run directly in parallel. I cannibalised a USB cable for its male socket, and soldered it (with a bit of its flex) to the speaker wires. The USB wires were quite flimsy, so I reinforceded the joint by gluing, sliding over some bits of thin plastic tubing and wrapping with duct tape.

      The clips are a very tight fit onto the tripod legs; with hindsight I’d try to find some slightly larger. I’d planned on adding and removing them as needed, but decided to leave them permanently attached:

       
       
      Total cost: £8.39
       
       

       
    • By Harmann Multani
      Hey everyone,
      I'm new to visual astronomy and I have an Astromaster 130EQ by Celestron. I have a problem with my tripod. It is the standard stainless steel tripod which comes with the telescope. I am having issues with leveling it as it bends as soon as the weight of the counterweights, mount and optic tube is put. Please help me.
    • By MrGuGuZai
      Hi, i just bought a skywatcher mak 127, when arrived i only realise i bought the OTA without mount. so i ordered az gti mount, because of covid 19 lockdown in my country they can only deliver after the lockdown period.

      my question is can i use mak 127 on a camera tripod temporarily? i had this https://www.samurai-...samurai-pro-888. it show can support 5kg max.
    • By vineyard
      Hello,
      I have a mint condition HEQ5 tripod for sale.  3/8" thread mounting bolt, spreader bar, 1.75" diameter legs.  Its never been used (I got it as part of an overall package, but I already have a Berlebach I use).  Still with the original polystyrene at the ends in the box it came in.  These sell for GBP109 new.  Happy to sell it for GBP70 plus postage (which in the UK via hermes should be about GBP9) or to hand over boxed in person (London).
      I'm new on SGL so don't have ratings here, but I do have 100% ratings on eBay.  Figured I would offer it on SGL first as I enjoy the community.  If no takers, then will offer it on other sites.
      Cheers,
      Vin
      ***** REDUCED to GBP 70 + p&p as I have a ZWO I need to pay for   *****



×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. By using this site, you agree to our Terms of Use.