Recently Browsing 0 members
No registered users viewing this page.
I've finally got around to making my flats box.
I decided to go for a cylinder rather than the normal square as I thought it would maximize the amount of reflected light and limit any 'dead' areas. I could also use the Celestrons dust cap retaining pins to lock the flats box onto the 'scope.
I purchased some of the craft board that has a thin foam sheet sandwiched between two sheets of thick paper/thin card. In order to bend the card into a cylinder, I creased the board every 20 mm by pressing the edge of a steel ruler into the board. It took two of the sheets to make a cylinder big enough to fit my C9.25, with only a couple of cm trimmed off.
I then made a reinforcing ring/defuser holder from two strips of the foam board; this time creasing them at 15mm intervals. I stuck these level to the bottom edge so the joins were 90° to the main cylinder joins. These strips were cut wide enough to ensure that the diffuser cleared the secondary housing.
The cylinder was designed to lock into the C9.25s dust cap retaining pins so next I cut two keyways into the bottom outer side. They looked a little weak so I reinforced them with some Christmas chocolate reindeer plastic packaging!
Although the foamboard is quite shiny, I wasn't happy with all the grooves, so I lined the inside with white A4 paper. The Perspex sheet was cut to shape and hot glued into place onto the ledge.
Next, starting at the top, I notched the edge of the cylinder to run the LED string lights cable through and then started to spiral the LEDs around and down the cylinder.
The top cap/reflector was made from two discs of foamboard. One to go inside the cylinder and one to sit proud of the edge. They were glued together before being hot glued onto the top of the cylinder. The LED light string that I bought has an integrated on/off button as well as both up and down brightness buttons with a 3M sticky pad on the back, so I stuck this to the top cap.
As I had previously made myself a 'scope mounted power distribution box with aircraft sockets for power, I removed the 3 pin UK plug/ac-dc converter and soldered on an aircraft plug to match my 12 volt DC supply socket.
The lightbox illuminated.
[A few more photos are in the imgur album]
Made this telescope for observing sunspots. The Sun gets projected onto a piece of paper after bouncing from 3 mirrors inside the frame.
It's compact, light, takes only a few seconds to point at the Sun, and sketching sunspots is as easy as circling the spots on a piece of paper.
It can even project the Moon:
The design is inspired by a commerically available telescope, but I’ve done all the designing myself, just for the fun of it.
Sunspotter is full of little details that make it interesting. How do you fix the eyepiece in the exact place where it needs to be? How do you keep the lens in place and perfectly aligned?
Building the telescope was a lot of fun, I’ve learned to use a jigsaw, X-Carve and a 3D printer. The plan is to use it to complete the Astroleague Sunspotter Observing Program, but unfortunately I completed it at the minimum of a Sun cycle, and won’t see any sunspots until next year.
Magnification: 75x Size: 41cm x 41cm x 15cm Weight: 1kg Design: Keplerian Projection size: 75mm Materials needed:
Lens: Ø52mm f=750mm achromatic doublet Mirrors: 1, 2, 3 Eyepiece: Baader 10mm ortho 1.5m² of 10mm plywood Wooden glue 5m of PLA filament 12 nails Compressed air Isopropyl alcohol Tools I used:
Jigsaw with a 30° bevel capacity X-Carve 1000 3D printer A laser pointer Clamp Learned modelling basics in:
LibreCAD Easel TinkerCAD Fusion 360
Part 1: Choosing the lens
The idea of a sunspotter is that the light goes through the lens, travels inside the telescope, bouncing from 3 mirrors, enters an eyepiece and the image gets projected on one of its sides.
The distance the light travels before entering an eyepiece is the focal length and it determines the size of the telescope.
I chose a Ø52mm f=750mm achromatic double. Observing the Sun doesn’t require a large aperture, 50mm is more than enough. I wanted a high magnification and went for the longest focal length I could find, which was 750mm. Achromatic doublet design is what people use in refractors. If it is good enough for a refractor, it’s definitely good enough for my project.
With the focal length chosen I could design the wooden parts. A drawing showed that the frame needed to have sides 30cm long, but I wasn’t sure about the placement of the mirrors and went for 31cm sides, planning to shorten the light path as needed by adjusting mirror positions.
This is the LibreCAD drawing of the layout of parts on a piece of plywood:
Part 2: Building the base
Having a drawing of the base in LibreCAD, I printed the drawing 1:1 scale on multiple A4 sheets of paper and glued them together. I transferred the drawing to a piece of cardboard and cut it out.
Applied this cardboard template to the sheet of plywood, and cut out two parts with a jigsaw.. I’m not an experienced user of jigsaw, and couldn’t manage to cut half-circles accurately enough. Even worse was that the two parts were very different. I didn’t want the frame to randomly tilt left or right when adjusting its altitude, and had to spend a lot of time with sandpaper to make the halves as similar as I could.
Glued the two large parts with three small parts in the middle. Additionally nailed the parts and the base was ready.
Part 3: Frame
The frame is simply a triangle made of three pieces, with short sides cut at a 30° angle. Most jigsaws can cut at 45°, but not at 30°. Had to buy a new jigsaw with a 30° bevel capacity.
Cut out three sides, cut short sides at a 30° angle, but didn’t put them together just yet.
The lens needs to be perfectly aligned with the Sun-facing part of the frame, otherwise the Sun projection isn't circular but elongated.
My solution was to carve a hole with a little step as shown on the image.
The inner hole is Ø46.5mm, the outer hole is Ø50.8mm.
The outer hole is the exact size to let the lens fit, but with a little bit of friction. Had to carve several holes to find the minimal size the lens could fit in.
The step is just large enough to have enough surface for the glue to keep the lens in place, I didn't want to reduce the aperture too much.
I used an X-Carve for carving and Easel for modelling.
With all 3 sides ready, I could assemble the frame. It appeared that my 30° angle cuts were not very precise, but after some sandpapering the sides started fitting together alright. Glued the parts together and left them to dry for a day. To apply some pressure on the joints, I wound several twine loops around the frame really tight, made sure all sides fitted well together and left it to dry like that for a day.
Part 4: Mirrors
When selecting mirrors I was looking for the smallest mirror that fit the cone of light. Small mirrors are a lot easier to place, and they let me better control the length of the light path. I considered using elliptic mirrors, but they were bulky and really hard to place. All mirrors are first surface mirrors, otherwise planning their locations would be a lot more confusing.
This was my original plan of placing the mirrors:
As you can see, all the angles and distances were carefully measured, and I wanted to simply make mirror holders of those exact dimensions. This was clearly a bad idea.
I 3d-printed some parts like this:
And only later I realized that the frame angles are not exactly 60°, and that there are drops of glue along the edges that don’t let me fit the pieces deep enough in the joint between the sides.
I cut angles from all the mirror holders:
After I put the first mirror in place I realized the angles are all wrong, and that I needed to re-do the holder. Separating the mirror from the holder was a huge pain, which resulted in an accident. The mirror fell off the desk and got damaged.
Luckily, only the back side got damaged, the front side was still working:
The final designs of mirror holders looks like this:
The holes in the front surface let me apply pressure on the back of the mirror if I ever want to separate it from the holder. The recesses collect the excess glue to avoid mirror skewing when gluing them.
All other holes are simply to save the filament.
Part 5: Placing mirrors
What I learned is that you can’t plan positions of several pieces with high precision and just hope that it all comes together. I needed a feedback about the precision of mirror positions.
I used a laser pointer to verify mirror positions at each step.
In the picture you can see that the laser is firmly set in a hole in another piece of wood, with layers of isolation tape on the tip of the laser pointer to make it stable. A clamp holds the piece of wood in place, ensuring that the laser ray goes in the same direction as a solar ray would. A crosshair of black thread at the center of the lens ensures the laser goes exactly through the center of the lens.
When placing each mirror, I marked the spot where I expected the laser to end up. While gluing the mirror holder to the frame, I kept the laser as close to that spot as possible. If for some reason, the laser couldn’t hit the expected spot, I did my best with placing the mirror, and recalculated locations of the following mirrors.
I saw the first sunspots after placing all the mirrors and simply holding an eyepiece in hand.
Part 6: Eyepiece holder
I tried eyepieces of different focal length and liked the picture I got with a 10mm eyepiece the most.
An eyepiece needs to be in a very exact spot to produce a sharp image. At this point it was obvious that my frame doesn’t match the model, and that I didn’t even know what exactly was wrong with the frame. I didn’t want to rely on the model and moved forward with trial-and-error.
I printed several parts to hold the eyepiece, with different eyepiece locations:
The part in the photo was a total disaster. It needed quite a lot of filament, at the same didn’t have enough surface area to be glued to the frame, and not enough surface area to hold the eyepiece firmly.
The next iteration was a lot better:
This part has a lot more surface area, and needs less filament to be printed. I intentionally printed the hole for the eyepiece too small, and had to sandpaper it a little bit, to make the eyepiece stay firmly fixed.
Adjusting the focus is done by sliding the eyepiece up and down until the Sun becomes a circle with well defined borders.
Part 7: Dust
All optical parts should be kept clean. Dust on the mirrors and the lens will make the image darker. Dust on the eyepiece will show up as artifacts on the projected image. Unlike sunspots, the artifacts will not move with the Sun. To clean the eyepiece I used compressed air. To clean the mirrors I used isopropyl alcohol.
Part 8: Fire safety
Don’t leave devices with magnifying lenses lying around. Once the Sun happened to be in such a spot that its light went right through the lens, burning through the cap of the eyepiece. Luckily, nobody was hurt and no other damage was done.
Part 9: Future work
Build quality of the base is very poor. The frame tilts sideways when adjusting its altitude despite all my efforts. I’d like to build a new base, but leave all the work to the machines. I already have a model for an X-Carve to make both base parts, compatible with my current frame:
A notch along the edge of the half-circle should eliminate the tilt. The precision of the machining should make the base very stable. Maybe next year, when sunspots become a common daily sight, I’ll get to this project.
Thank you for reading this far!
I hope you enjoyed it.
It's been a long time since I've posted in this forum, anyway I've picked up a Skywatcher 200p F/6 dobsonian as a DIY project whilst I continue to work on a new telescope from scratch, (I've started to grind the mirror).
I'll be making improvements to this dobsonian as a project and learning experience, I've already got a temperature controlled fan which has a probe that can measure both mirror and ambient temperature. I'll be measuring the primary mirror with my in progress Foucault/Ronchi/Bath Tester when that's finished in the next couple of weeks, may even refigure it depending on results.
But I'm most excited about this right now. The blackest Black Paint as an alternative (hopefully better alternative) to flocking!
This stuff is seriously black and flat, I backed it on kickstarter and received 3 bottles along with goodies.
I plan on painting the area opposite the focuser, area around the primary mirror, inside the focuser drawtube, potentially the secondary mirror holder and edge of the secondary also.
It's a shame I don't have any flocking to compare it with but it looks incredible.
This video shows just how impressive it is (moreso than my little tester I've done).
I'll try and get some decent before and after pics.
In the famous words of Bilbao Baggins, I'm going on an adventure!
Almost 2 years ago i got rid of my old shed with the intention of replacing it with a R O R shed,
Well a lot has happened since then, but no R O R shed ? No way i could build one, my DIY skills are rubbish.
My mount and scope plus other bits have sat in the garage ever since, mainly because it's such a pain to drag everything out and set up only to be thwarted by cloud/rain, so i decided that they would stay in the garage until the arrival of R O R shed,
so fast forward 2 years.....
Well! while browsing some astro sites i happened across an advertisement which said something like wooden observatory for sale, 7ft x 7.5ft, buyer to dismantle and remove, so me being in need of one had a look at the pictures he posted, that will do nicely i thought, so i contacted the seller and asked for more info and pictures,
It's not a roof that rolls off onto supports, it turns out 1/2 of the roof rolls over the other 1/2 with a front section of the shed that drops down,
I was happy with what i received from the seller, he couldn't have been more helpful and seems a really nice bloke,
Right then, where are you located mate i asked,
Bovey Tracey he replied,
to be honest, i had never heard of it, so time to consult google maps..
Well it turns out it's only about 270 miles one way from my house in Lancashire ? (so round trip of approx 540 miles)
Time to make a decision, do the positives outweigh the negatives, is it going to be a cost effective solution in getting my R O R shed ?
after doing some calculations and a little more contact with the seller, the answer to the 2 questions above is YES ?
I have hired a box van for this coming Saturday,shangied my brother in law to accompany me and..
I'm going on an adventure to Bovey Tracy to dismantle it and give it a new home in sunny Lancashire,
even though my DIY skills are rubbish i feel i have to give this a go,
All in with the cost of The Obsey (as it is now known until i can think of something better) and with the hire van/fuel and brother in laws dinner
it's going to set me back approximately £570 and a day out, I'm well chuffed with that, the cheapest quote i had to have one built was £1000
I have a couple of pictures of the obsey in it's current location if anyone would like to see them,
Sorry to waffle on so long,
Thanks for reading
My diy Onstep GoTo controller is basically an Arduino Mega 2560 with a RAMPS 1.5 shield, rated for 12V normal, 20V max & uses about 2A max.
It is powered from a 12V car battery. The lead has crocodile clips at the battery & connects to 5A screw terminals on the RAMPS.
When I "power-up" by connecting the clips there is a spark at the terminal. This is expected, but does the sparking reduce the life of my electronics?
If so is there a cheap/simple way to reduce or prevent this?
I know I could put a switch in the lead but I assume the sparking would then happen inside the switch, making no difference.