Jump to content

stargazine_ep39_banner.thumb.jpg.b87bddaa2aded94d2a3456c0589a82b9.jpg

Recommended Posts

Hey guys. Looking for advise from any one who has a horizon 8115 heavy duty tripod. It's fantastic for my 15 x 70 Helios apollo, I'm seriously looking to get the 28 x 110s but as they are very expensive I don't really want to be spending more cash on another tripod. Would they be ok to hold the bigger bins. Cheers and TIA

Link to post
Share on other sites

I tried the Horizon 8115 with a pair of 25x100's a couple of years back and found the tripod did not cope very well I'm afraid. There is a really big jump up in size and weight when you reach 100mm or larger binoculars.

I felt that the limit of the Horizon 8115 was probably around 80mm binoculars.

 

 

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By elbaztardo
      Atik Horizon Mono
      EFW2
      Baader NB and LRGB Filters
      Boxed with cables.
      Looking for £1500\€1600
       
    • By andyrawlins
      Hi All
      After much research, primarily on this site and The Binocular Sky, I got hold of the above binoculars.  I spent ages writing a review specifically for this site of what I found, as a thanks for all the advice I had received.  By the power of idiocy I then managed to post it on Cloudy Nights instead (I had both open in my browser).  Too much Christmas port I guess  
      Anyway, too late to take it down as some have already replied and I guess I shouldn't post the same thing on two sites so here is a link to my review on completely the wrong site   No offence at all to Cloudy Nights but I wrote it with the Stargazers Lounge audience in mind and it may make less sense on a US site.
      Comparison of Pentax SP 50 WP 10x50 and Nikon Action EX 10x50 CF




    • By Zermelo
      I saw a suggestion somewhere (possibly in SGL) to attach lights to your tripod legs (dark-adaption-friendly ones, of course). The idea being to avoid accidental collisions, especially at star parties or outreach events. We experience this quite regularly at home too, so I decided it was worth pursuing (and also, as users of go-to functionality, I’m getting tired of repeating alignment operations throughout the evening).

      The very simple idea was a (removable) clip for each leg, each with an LED. I briefly considered a self-contained battery to power each, but decided that charging them was too much hassle (and I also doubted finding LEDs that would operate at such low voltage). Instead, they would be fed from the USB port on the power supply I previously rigged up. I thought the LEDs would be more noticeable if flashing, and found these.

      My SkyWatcher 150i tripod has 1.25” upper legs and 1” lower. Since collisions are most likely with the lower legs, it was that diameter I worked with. I looked for plastic pipe clips of this size (the most common ones are 15mm and 22mm used for plumbing) and found these. They have a hole for a fixing screw that can be used to hold an LED, and they have a hinged collar for holding the tube, which preserves a gap that allows electrical connections to pass.

      The screw hole in the clip was wide enough to admit the LED body but not the rim. To allow the LED to protrude from the clip I drilled out the holes a little wider, and about 2/3 of the distance through the clip. The LED could then be pushed through until the rim engaged, and the terminal leads were bent into a succession of right angles to guide them to the top of the clip. I found some twin speaker wire in my junk box, and soldered lengths to each LED’s terminals. The clips have a channel along the edge to allow them to be ganged together. I opened them out with a needle file so that the speaker wire was a tight fit when pressed in – this was for strain relief.

      I covered over the soldered joints with some scrap plastic strip, screwed into the clip, and pushed some Araldite into the hole and around the exposed metal, to prevent shorting:

       
      These LEDs seem to work on 5.1V without needing a series resistor, so I twisted the positive and negative ends of the three speaker cables to run directly in parallel. I cannibalised a USB cable for its male socket, and soldered it (with a bit of its flex) to the speaker wires. The USB wires were quite flimsy, so I reinforceded the joint by gluing, sliding over some bits of thin plastic tubing and wrapping with duct tape.

      The clips are a very tight fit onto the tripod legs; with hindsight I’d try to find some slightly larger. I’d planned on adding and removing them as needed, but decided to leave them permanently attached:

       
       
      Total cost: £8.39
       
       

       
    • By Ade Turner
      I’ve been using my 8’ Edge HD on an Evolution mount for a couple of years now and I added a wedge to it a few months back. Using SkyPortal with StarSense I’ve never really had any major issues getting it aligned. 
       
      Last night I was setting up to photograph Mars and went through my normal procedure. StarSense took its images but, after confirming success with the third plate, instead of just winding up a bit and parking it proceeded to pitch the ota towards the north well below the horizon.
       
      Fortunately nothing snagged. I skipped the ASPA and instructed it to goto Mars and was surprised to find it was spot on (better than usual actually).
       
      Anyone any ideas why it took that nose dive? Thanks.
       

       
    • By Harmann Multani
      Hey everyone,
      I'm new to visual astronomy and I have an Astromaster 130EQ by Celestron. I have a problem with my tripod. It is the standard stainless steel tripod which comes with the telescope. I am having issues with leveling it as it bends as soon as the weight of the counterweights, mount and optic tube is put. Please help me.
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. By using this site, you agree to our Terms of Use.