Search the Community
Showing results for tags 'sgpro'.
Found 5 results
Hello, I have a remote telescope set up in Spain. It has an Atik EFW3 7 position filter wheel. I use Seqeunce Generator Pro to control the set up. I was advised by the owner of the remote site that he uses a Pegasus Astro Ultimate Powerbox v2 which considerably simplified the cabling. So, I decided buy one also. It was installed a few days ago. However we have been having significant problems with the filter wheel. Before the Powerbox was installed, the filter wheel had performed flawlessly for over a year. The problems are:- The filter wheel, on start up, often does not move when commanded to do so in SGP. It sometimes says "Moving" in SGP but then stays at the Luminance filter which is in Position 1 on the filter wheel. If I close both SGP and disconnect the Powerbox and start again, it then sometimes (but not always) starts to accept instructions to move correctly for filters 1 to 5. However, even when it is moving the filters correctly, filters 6 and 7 are inaccessible. It acts like they are not there at all. The site owner has checked the cables and they are properly installed. Can you please offer any advice on how to proceed? I do like the Powerbox concept and hope I can continue to use it. Thanks for looking. Eric
TLDR: If you change an Equipment Profile, you need to use "File -> Apply Profile to Sequence" to update the Sequence. For Every Sequence you have that uses that Profile. I spent quite a bit of last night pulling my hair out in frustration when SGPro decided that it was not going to wait for PHD2 to settle after dithering, SGPro just went blindly on and started the next frame, which of course led to horrible star tracks and subs that had to be thrown away (not something to do lightly given the poor weather recently). After much experimentation I found the solution, and as I had not discovered it through my googling online I thought I would share it here in case anyone else has a similar problem: Some scene setting; SGPro works using three main "Objects": 1 - The User Profile. This is the geographic location of the observing site and the details of the observer. 2 - The Equipment Profile. This is a set of equipment that is used together (scope, camera, filter wheel, guide scope, plate solver etc). 3 - The Sequence. This is one or more targets that you wish to image along with their RA/DEC and the number of each type and duration of frame you wish to take. One of your equipment profiles can be chosen as the default for all new Sequences. You can then either create (using the File Menu) a "New Sequence" (using the default Equipment Profile), or "New Sequence from Profile" which lets you chose a specific profile (if you have different set ups for wide field nebula or deep galaxy hunting). You can also associate a User Profile with a sequence. You can even change which User Profile a Sequence uses from within the Sequence (in case you take images from different sites). What you can not do easily is change the Equipment Profile associated with a Sequence. I spent ages changing my default Equipment Profile (the one that the Sequence was using) and it was having no effect. It turns out that whilst the Sequence links to the User Profile, when you create a Sequence it takes a copy of the Equipment Profile at that point in time. any changes you make to the Equipment Profile after that are not changed in any Sequence that is using that Equipment Profile. To make matters worse, there is no way of changing much of the equipment settings once they are embedded into the Sequence. So I was changing the Dithering, Settling accuracy and Settling Time in the Equipment Profile and it was having no effect. So if, you make a change to an Equipment Profile, once you have saved the profile, you need to open up your sequence and selected "File -> Apply Profile to Sequence" to change the Equipment Profile information stored in the Sequence itself. Then the next time you start your sequence the correct equipment values will be used. Unfortunately SGPro does not inform you that the Equipment Profile has been updated since you last used the Sequence, so you will need to do "Apply Profile" every time you open a Sequence just to be sure.
As SGPro are actively promoting the FocusLock focussing system from Optec Optical & Electrical Products. I was wondering if anyone is actively using this system. Preferably with a Lodestar or LodestarX2 and OAG, using the Lacerta kit. Steve
Ok, after a stalled attempted a few months back, I am now determined to learn how to use SGPro for helping out with my imagining sessions. Going to be lots of questions over the next couple of weeks, and the first one is pretty basic . I am using an Atik One 6 CCD camera which has a built in filter wheel. Does anyone know what driver (ASCOM?) I need to use so that SGPro connects and controls the filter wheel properly? I am proberly doing something stupid, but none the the dropdown ones seem to work .
Hi So, tonight was my first clear night in months. Got all set up. Went to use APT to capture images to polar align the mount, could see nothing. Just black. I don't know if it was APT playing up or if I was doing something wrong. The histogram showed data, so i moved the white / black points but still got nothing. Just grainy black. Annoys me that there is no auto stretch... Went back to the old faithful Nebulosity, and captured a preview. Stars were seen! So, seems that APT was having issues. Then the clouds rolled in. Another night bites the dust. My question is: do people use APT or something else for CCD images? I've heard good things about SGPro, but not sure. I like the sequencing / filter wheel control offered by something like APT or SGPro rather than nebulosity. What are people's thoughts? Thanks Joe