ispookie666
New Members-
Posts
25 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Blogs
Everything posted by ispookie666
-
POE is fantastic and I use it around my house. But most are around 40- 57V, you would need to look into Passive POE to make this work. Again, the voltage injected will be usually 24V and above. Might need a DC - DC converter at the end. Might be easier to just use https://www.amazon.co.uk/gp/product/B07L6WLR51/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 and a Power bank with 12 V output to feed the one above. I have installed the above and installed an Outdoor ethernet socket in a BG single gang outdoor switch, the outdoor socket is connected to a wall ethernet socket. Once I set it up, I can stay indoor 😀
-
Thank you for the inputs. I honestly have no idea about the median! What should I be using? I'll check my DSLR and find out more. I had another go tried my SW 200DPS, just could not get tracking to work, used a 250mm lens f6.3, the results were even worse. I'll stick to my tokina or give the skywatcher 200 another go. Thank you once again.
-
Soul Process 3.TIF Tif file from DSS
-
The second image is straight out of DSS. It looked so dark, hence not looked into processing
-
Lol way off mark then. Thank you.
-
Just about managed to setup my rig. Was trying to photograph the Soul Nebula. Nikon d5000, ISO 400, 45sec, Tokina 105mm F2.8 No filters. Mount - CG5 with EQStar EQ5, PHD2 tracking using ZWO 120 as guide camera The below image is a output straight from DSS - I think 70 frames, some dark bias and flat frames I thought I might be getting a lot more data after stacking - any pointers? or what I should be doing differently?
-
Have been using the EQ Star Pro version for CG 5 and cannot fault it. Connected to EQMod, PHD2 and Gamepad . Using stellarium is a lot easier compared to the handset. Managed to auto guide and it was not too bad. Have only gone for 45sec ISO400 exposures and have not seen any star trails.
-
Sodium Vapour Light
ispookie666 replied to ispookie666's topic in Getting Started General Help and Advice
I think the council have done something. They have added a light diffuser at the tethered end which has reduced the light spillage into the garden. Its only there on two light posts which I had reported. Cannot complain ☺️ -
Collimation woes
ispookie666 replied to ispookie666's topic in Getting Started General Help and Advice
Wowsers 🤪 -
Collimation woes
ispookie666 replied to ispookie666's topic in Getting Started General Help and Advice
Thank you once again everyone. Decided to revisit collimation and got it done. 🙂 -
The motor control firmware is 5.14. After a bit of digging around, decided to get the EQstar Pro.
-
Collimation woes
ispookie666 replied to ispookie666's topic in Getting Started General Help and Advice
Thank you everyone. Slowly getting the hang of it. Looks like the spider vanes were off , adjusted them. Tweaked a bit of primary mirror and have finally got things kind of collimated. Will check again tomorrow -
No end to my various problems. I have a Sky-watcher 200PDS and the views were a not very sharp. Been trying to collimate the scope using a cheshire, for the life of me cannot get the mirror clips in sight, at the most I can get two. I was following @Astro_Baby guide and got the Secondary mirror to be a circle (it was pretty much elliptical at the start). have been stuck trying to get the clips in view. Any help appreciated, even better - anyone close to cambridge wiling to help. 😐
-
To reflash fhs firmware, I thought I would need it!
-
I'm new to all this. The GoTo handset is old and has something like an RJ11 socket. Does this need a RJ11 to usb convertor?
-
Thanks for the review. I'm looking into getting a EQ star pro, could you point me as to where you sourced this from?
-
I recently bought a used CG5 mount with Advanced GT. Used it a few times but yesterday had a runaway RA motor. Is there a ready replacement or preassembled kit to replace the motors and controllers on CG5. I had a look on OnStep, but boy thats a lot of tinkering - would be great if there was preassembled kit. Or any other suggestions. May just cut my losses and buy a new mount🤐
-
Just about starting with star gazing, trying to find the best possible way to maximise the options from my house (have this as part of another thread) https://stargazerslounge.com/forum/19-getting-started-general-help-and-advice/ The sodium vapour lamp is just spilling light into the garden. Other than putting up a big sail during observation, don't know what else to do. Part of my garden is well shielded and have reasonable view of the sky, but polaris is shielded by the house. Is there a way to get polar alignment without polaris?
-
Sodium Vapour Light
ispookie666 replied to ispookie666's topic in Getting Started General Help and Advice
Will do. The light spill is really bad. Makes most of the garden pretty unusable, the night sky from the shielded part of my house is just amazing. -
Sodium Vapour Light
ispookie666 replied to ispookie666's topic in Getting Started General Help and Advice
Emailed the council's street lighting section. I'm not holding much hope. Maybe the follow up would be adding light nuisance, trespass etc. Still waiting for my sky watcher 200p -
Newbie here! Used to have a star travel a while back. Slowly getting back into stargazing. I live in a Bortle 4 area and the sky is beautiful, except a sodium vapour light just next to my house (unfortunately its on all night due to a Cross junction and a railway crossing) which spills light onto my garden and patio. Will using a light pollution filter help filtering the light out?