rohanpai

hi @david_taurus83 - yes, i took this with the camera on the scope. I suspect there was light leak from near the OAG and I was taking these darks in daylight. I took darks again last night and they don't show this pattern anymore.

I am using ASI1600mm and captured dark frames at 300sec and camera cooled to -1C. When stretched, the frame shows a wavy pattern from top right corner. Does this look like a light leak?

Thanks. I was expecting them to be moving much more I'll try different dither settings next time on the same target. Weird enough, I used the same setup and setting to image the Carina nebula and this noise pattern didn't occur. The only difference was the sensor temperature (i wasn't cooling the camera for both sessions - so Carina was about 15C and Dragons of Ara was about 11C) and I did not have my dew heater strapped around the OTA for Carina.

I have this as my settings in PHD2. I am not sure if PHD2 will do the minimum configured move and then go ahead with the next capture. Should I try changing this? My imaging camera is a asi1600mm with 3.8um pixel size and guide camera is a asi120mc-s which is 3.75um pixel size.

I used sum stacking and I don't see any hot pixels along a straight line I was dithering using a asi120mc-s with OAG. I can try dithering to 12pixels and see if tht makes any difference.

Hey mate Not sure how I can stack without pixel rejection. Can you help with what settings to use in DSS or Siril or PixInsight? I've got all 3 running at the moment ..

HI David I will imaging using a WO ZS61 and ZWO 1600mm. I gathered another 2 hours of data today. Stacked it all and see the same noise pattern on today's stack as well.

Hi Olly 1) Do you see any trace of this type of noise in single subs? >> Yes. I can see some on a single sub as well. I have attached a single sub with Ha filter and Oiii filter. 2) Try stacking without darks, then without darks or flats, to see if they are introducing the noise. They may be. >> I tried this and got the same result. The stacked image shows the same noise pattern 3) Check your stacking parameters. Try different ones, ie Sigma, Median and Average. 4) Try a different stacking program. (You can download AstroArt for trial. It won't save but it's a great stacking-calibrating program. >> I tried Siril and DSS and PixInsight. All 3 gave similar results I was imaging the Dragons of Ara (NCG 6188). I did a auto stretch in Siril and PixInsight after stacking and saw this noise. Even with manual stretch, I could see the noise start to show up quickly. Oiii filter.fit ha filter.fit

Need some guidance here.. I got about 2 hours of data in total with Ha and Oiii filter. I had good polar alignment, guiding was going well and I was dithering after every image. I stacked it all this morning with darks and flats and the image has walking noise. If I am dithering, should it not eliminate the walking noise? Can this be due to dew?

Hi @michael8554 - I tried your recommendation of pulling the camera out of the focuser and managed to get focus. So I need more distance between the focuser flange and the sensor.

Hi all I connected a Touptek gpcmos02000kpa to Skywatcher 200PDS (hoping to get some videos of the moon), but could not get any focus. I suspect I need to have a certain backfocus distance to get image on the camera sensor. Anyone has tried this setup? What is the recommended backfocus distance? Thanks in advance. Rohan.

Thanks, @malc-c

Hello! Would this power supply adapter work for a HEQ5 pro? 10A/8A/6A Power Supply Adapter AC 100 - 240V to DC 12V Transformer Home Office - Kogan.com Thanks! Rohan

Hi @Dougie Smart - I bought a Bresser full HD camera. Installed Toupsky and the ASCOM driver for Bresser. Connected it to my laptop via the cable provided with the camera. Opened Toupsky - it did not detect the camera. Opened SharpCap and it did not detect the ASCOM Bresser camera... Did you have to do anything different to get the camera connected? There is a little red indicator at the back of the camera. Does that turn on when your camera is detected, or is that only when guiding?

Thanks Alan. Will try it out …