Jump to content

 

1825338873_SNRPN2021banner.jpg.68bf12c7791f26559c66cf7bce79fe3d.jpg

 

Bizibilder

Moderators
  • Posts

    16,889
  • Joined

  • Last visited

  • Days Won

    8

Everything posted by Bizibilder

  1. Just to add that getting the whole darn thing carefully balanced will help. Just a little out of balance can make the motors very unhappy!
  2. Tonights almost Full Moon - A nine pane mosaic each from 200/1000 frames through the ED120 APO and ASI 120mm mono camera.
  3. A swift Venus image from this evening - 200/5000 frames using the ED120 APO, 2.5x Powermate and ASI120mm mono camera in truly awful seeing!* But it is my first Venus image for a few years so I'm happy with it. * The seeing was really bad as I had several laptop crashes which I eventually found to be caused by a dodgy USB cable. It meant that by the time I had sorted everything out Venus was down on the neighbours rooftops with the resulting severe boiling and heat haze.
  4. How many revolutions will your EQ6 do in its lifetime? I suspect your generic bearings will be good for a few thousand rpm for many hours running time. If you install your bearings (any type) correctly and with the correct preload (i.e minimal play) and keep them properly lubricated, they should outlast the mount by a considerable margin.
  5. Cheap second hand laptop with as many USB ports as possible! I used this company Morgan on several occasions (usual disclaimer).
  6. Try Googling "Drum case". Seem to be some around £50 that are the size you require - They do both soft and hard (Fiberglass and/or moulded plastic) types. There will also be a second hand market for these that may be worth a try on the usual sites.
  7. My first "Moon" for almost a year! (last one was 10th Feb 2019!!!). Been a bit busy lately. Also surprised myself that I could (almost) remember what to do to control the scope, camera and get an image - there were a few naughty words spoken getting everything working properly. The kit was fine - it was just me being a bit rusty Seven mono panes with 200 from 1000 frames stacked in each.
  8. Looks like a good design you have there. Just one comment - have you considered replacing the two internal stud partition walls with a simple single sheet of plywood (18-20mm thick)? This will have similar strength (as in bracing the whole structure) even with a doorway cut into it and will gain you about 8-12 inches of extra useful internal space.
  9. Personally I would steer clear of inverters to run laptops (or any other Astro grear) - much easier to use an "in car charger" to run direct off 12v. If you use an inverter you are fighting the inefficiencies of both stepping up the voltage and then stepping it back down again.
  10. Just add up the total Amps drawn by your equipment and then multiply by the number of hours you expect to use them. For example: Mount 2 Amps, Camera 2 amps, Laptop 4 amps and Dew heaters 2 amps is a total of 10 Amps. If you run for 5 hours then 5 x 10 is 50 Amp hours. This would work on a 100 amp hour battery (it is inadvisable to run batteries down below about 50% of capacity). Please note the numbers above are just guesses! You will need to work out the exact values from your own equipment. I used to use a 100Ah battery with an EQ6, DSLR camera and laptop and never had issues with running out of power for a 5-6 hour session.
  11. They are most certainly NOT the same as standard photographic filters. These foil filters are used for "white light" solar observing and photography - ie they transmit all wavelengths in the visible spectrum. An Ha 7nm filter is NOT the same as a proper Ha solar telescope. Unfortunately a true Ha telescope (or device like the DayStar Quark solar "eyepiece") is a very expensive piece of kit! One safe alternative to the foil filter is the Herschel wedge diagonal - but again this is quite an expensive alternative. (Just an afterthought - there are "Solar Filters" that can be screwed into a normal eyepiece. These used to be sold with cheap telescopes. They are EXTREMELY dangerous!! They will shatter in the heat from the Sun and, should you be looking through the telescope at the time you will be blinded. Don't even think of using one!!)
  12. I would advise you to use the Baader foil of ND5.0. This is quite safe for both visual and photography. The ND 3.8 foil is ONLY suitable for photography and NOT for direct visual observations. You can make a filter holder quite easily from card and strong tape. One sheet of A4 size should make at least two (possibly three or four if you are careful) filters. I keep my own filter in a plastic box with a lid. It is about five years old now and still in excellent condition - I am always careful not to touch the foil and to check the foil is in good condition before EVERY use.
  13. Assuming you mean space around the scope inside an observatory I would suggest 18" (450-500mm) minimum all round. That gives you just about enough room to squeeze yourself past the scope - assuming you are of at least only moderate proportions!! It also allows room for the inevitable additions and extensions to the scope that will happen as you use it.
  14. Yes - try some WD40 or similar to try and get into the joints. Then try using something like this rubber jam-jar opener (less than £2 on the bay of fleas): You may be able to get things moving. If not then try a little heat from a hair dryer (or hot air paint stripper gun but be careful!) When all else fails brute force may be required
  15. The Sun was out and I had time for some imaging today - even better as there is some activity! AR 2741 - 200/4000 frames with the ZWO ASI 120mm mono camera. The seeing was pretty poor!
  16. Should have said - Baader solar film was the only filter used (which by now must be about 5 years old and still going strong!)
  17. First Sun image since last August! Clouds, lack of any sunspot activity and a very busy life at the moment are my excuses! Almost forgotten how to process in addition to Windows complaining about any App that I used (PIPP, Registax5 etc!!) Anyway - stack of 45 from 138 single frames taken with the Canon 1100D and ED 120APO. ISO 100 and 1/4000sec (If I recall correctly).
  18. Today - probably the seeing. It was pants in white light!
  19. The primary of an f/15 SCT is an f/2 mirror. Take that away and replace with the hyperstar/camera and you have an F/2 set-up.
  20. Click here According to this announcement Microsoft will no longer force Windows 10 updates on you when you lest want them. It also looks as if they intend to test updates before springing them on unsuspecting users. A decent response at last to user complaints about windows 10 being a real pain!!
  21. In my observatory there is no door to the "warm room" section - yet it does keep the chill out and cuts any wind down to more or less zero. Once I'm gone the air can circulate throughout the building - there are plenty of gaps around the sliding roof and I have never noticed any condensation inside the observatory. I suggest you simply leave the warm room door open when you are not using it.
  22. A lovely sharp image - you've not lost "the touch"! Just a suggestion - instead of wavelets, try deconvolution. imppg will find it. Have a play - I find it far easier to use than wavelets, and it gives results that are at least as good!
  23. If I recall correctly ('tis a while since I used DSS!) you put all the calibration frames and first set of lights into the first channel and then just the next set of lights into channel 2 etc DSS uses the one set of calibration frames for each channel.
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. By using this site, you agree to our Terms of Use.