Jump to content

Stargazers Lounge Uses Cookies

Like most websites, SGL uses cookies in order to deliver a secure, personalised service, to provide social media functions and to analyse our traffic. Continued use of SGL indicates your acceptance of our cookie policy.

sgl_imaging_challenge_banner_globular_clusters_winners.thumb.jpg.13b743f39f721323cb5d76f07724c489.jpg

Gina

Members
  • Content Count

    35,010
  • Joined

  • Last visited

  • Days Won

    34

Everything posted by Gina

  1. Think I have the focus motor connected. Now just waiting for the stars. Camera cooling is better than before with the different waterblock. Now at -23°C. Desiccant is working - no condensation. I just plugged the air tube to the ASC to keep moisture out. I'll see if I can connect up the pressure system tomorrow.
  2. Well, I have the ASC installed on the north side of the observatory though not everything is working yet. I've connected up the dew heater and camera cooling and running the cooling water circulation. I have yet to connect the focus motor and the pressurisation system. I may get some of that done this evening but now I'm going to get myself some food. Meanwhile, here's the first image with the new version and a photo of the installation.
  3. Phew. Just struggled with the main seal, between the casing top and the base. Also bolted through to the mast connecting piece. 8 M4 bolts and nuts - pukka flange joint! Silicone sealant everywhere and a fair bit in the joint. I'm doing the dome seal last. That will let me fill the space with silica gel bags. Now taking a tea break.
  4. I see the inspection department has had a look ? Lovely doggie.
  5. Mast to ASC fitting completed. Wiring inside ASC completed. Waterblock clamped onto Peltier TEC and camera for camera cooling. Time presses on but I'm taking a much needed cuppa break... Whether I actually make it for this month's one clear night sky remains to be seen.
  6. Hopefully on the final furlong of the race to finish this incarnation of the ASC. I want it out there by tonight! Printing the funnel shaped support that connects the ASC to the hollow mast and sorting out the final camera asse4mbly and wiring.
  7. The shuttering on my block/pier just went down to about an inch below ground level. Just enough to hold it and stop the concrete running out. Screwing held the wooden parts together.
  8. Made an error in the design so now printing another casing top. Meanwhile, I've been working on the electrics and the air reservoir. I'll probably use a 2L milk bottle as that has a large enough lid to take two grommets - one for the air tube to the ASC and the other for a bicycle valve to apply pressure.
  9. HAT circuit modified. Currently printing casing top. Base and USB cable clamp printed and USB cable clamped and sealed.
  10. The village lights around half a mile away don't seem to be any problem but the expanding town of Honiton about 5 miles away definitely is, as are Axminster, Ilminster and even Taunton some 12 miles to the north over the hills. Bortle 4 skies here now - used to be Bortle 3 a few years ago.
  11. For higher quality Peltier TECs (at a higher price) I use Farnell Element14. Long lasting and higher efficiency.
  12. Slight rearrangement of component required for the latest dew heater and camera cooling circuit. Originally, the dew heater used an N channel power MOSFET with the heater in the power side. I wanted the camera cooler to work at two different levels of cooling - LOW to just keep the camera from overheating in daytime and HIGH for low noise at night. This was achieved by running on 5V for LOW and 12v (13.8v) for HIGH so the -ve had to be connected to power Gnd. +5v power was provided by a diode and HIGH by pulling up to 12v with a P channel power MOSFET. As a result the dew heater and camera cooler needed 4 wires altogether. +12v & dew heater and Gnd & camera cooler. To allow for only having 3 wires for both features I needed to arrange that they both used Gnd as Common with the dew heater in the Gnd side of the circuit. At first I thought of changing the circuit to a P channel MOSFET for the dew heater like the cooler but I don't seem to have any more. However, one advantage of using optocouplers id that the voltage between the driver and receptor can be up to 5000v so the standard N channel MOSFET circuit can simply have the load in the negative (Gnd) side. The optocoupler transistor emitter will be going from 0v to 12v as the dew heater is switch on and off. Also, looking at the component layout I see this is just a matter of removing a Gnd link and moving a couple of wires. This is the circuit diagram for the camera cooler. Dew heater circuit with heater in the +ve side. This photo shows the layout as used in the previous ASC version (called Ultimate). The two small black blocks to the right of the board are the optocouplers. They are linked by a short green Gnd wire which will be removed and the dew heater wire connected to the emitter of the optocoupler transistor (lower left pin). Near the RH edge of the board, the orange and red wires will be re-connected to the yellow +12v rail.
  13. I agree - first things first.
  14. Yes, I think I looked it up but it's a bit of a vague memory from 7 years ago now. Details are probably in one of my observatory build threads.
  15. I used the solar noon method. About 12:16 here - you have to allow for longitude.
  16. Busy printing the new parts. Well my Mini printer is - I'm busy designing them. (And watching Countdown ? )
  17. If using a compass, beware of the iron in the brake disc.
  18. Thank you for confirming my thoughts Tony ? I shall now start turning out new designs. A nice big reel of white PETG filament has arrived and I shall be using that. A better colour, I think, for a unit that will be in full sunshine (when we get it).
  19. I can seal the cable part of the USB lead with a hole for the plug and a block on the fixed base and a "plastic plug" to cover the base round the hole where silicone sealant is placed. Bolts hold it all together.
  20. I have some 7 core low voltage (automotive/marine) round cable I can use for the ASC if I put the RPi etc. in the observatory which can be used for the focus motor (4 wires), camera cooling and dew heater. Red, blue, green & black are the standard stepper motor colours leaving brown, yellow and white which can be Common, Camera-Cooler and Dew-Heater. That would just leave the USB.
  21. Bicycle valves have just arrived.
  22. Having worked out a way of pressurising the ASC enclosure with dry air and sorted out the sealing, I'm having second thoughts about having the RPi etc. up in the ASC casing. A few things really, perhaps the worst is that having the RPi+HAT in the ASC casing means that any alterations to either wiring or firmware would entail taking the whole rig indoors and breaking the main seal to gain access. Cooling the RPi and other electronics to cope with a possible summer heatwave, with the unit in the full heat of the sun, meant adding a heatsink to cool the air and hence the electronics, to keep it working. Also, I would like to keep the volume of air inside the enclosure to a minimum. The reason for having the RPi and other electronics in the ASC casing was to reduce the wiring etc. passing through the sealed bulkhead, particularly the awkward USB cable with a plug on each end, as well as all the other wiring (apart from power and pressure switch). I guess the problem of the USB cable could be got round by cutting the cable and rejoining it after passing through a grommet in the base - otherwise some printed parts to clamp together round the cable like I had before. I would appreciate any thoughts on this.
  23. Base finished and pipes & cable fed through. This is quite a lot heavier part than the previous base so I think it will be waterproof/airtight and I'm wondering if I can risk it being alright and go on and continue the whole assembly. There's some clear sky forecast for tonight, tomorrow night and Saturday night.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.